Chainrings

- Direct Mount Shiftring sets for TRS series cranks - Integrated ring set mounts directly to crank arm - 7075-T6 aluminum construction with 4mm width optimized for all chainguide systems to prevent chain jamming - Requires spider lockring removal tool

- Guidering M to fit any 4x104mm BCD crank - Dual width "M" (narrow/wide) tooth profile engages the chain securely even at extreme angles - 7075-T6 aluminum construction optimized for all chainguide systems to prevent chain jamming -1mm swappable chainline

- Patent pending, low weight, high strength, impact absorbing design - Captured aluminum inserts eliminate over-tightening of chainring bolts - Embossed chrome badging - BCD: 4 x 104 - Not compatible with pre-09 E-13 chainguides. 87g (36t)

The XTR M960, now 4 generations old in the XTR lineage, is an oldie-but-goodie crankset and Wolf Tooth aims to meet your 1x needs with these rings. Compatibility: - These rings only fit on the M960 crankset in the middle ring position. They are a 102mm BCD. - For 1x9, 1x10, 1x11 and 1x12 drivetrains (including SRAM Eagle) - Compatible with all 10, 11, and 12 speed chains (Including SRAM Eagle) - If using a 9 speed drivetrain use a 10 speed chain (shifts and works well on a 9 speed drivetrain and fits the ring tighter for better chain retention)

The 104 BCD chainring was Wolf Tooth’s first product ever and it is the most common bolt pattern on double and triple cranksets. Wolf Tooth’s patented Drop-Stop tooth design is the best available anywhere. Compatibility: - These rings fit any 104 BCD crankset - 30 tooth rings require chainring bolts that are 7-10mm long. All other sizes require single ring specific bolts that are ~6mm long. - 30t x 104BCD ring is the only QUARQ power meter compatible 30t ring available! - For 1x9, 1x10, ,1x11 and 1x12 drivetrains (including SRAM Eagle) - Compatible with all 10, 11, and 12 speed chains (Including SRAM Eagle) - If using a 9 speed drivetrain use a 10 speed chain (shifts and works well on a 9 speed drivetrain and fits the ring tighter for better chain retention).

416 stainless steel is not the first material choice for most component manufactures looking to use stainless steel (most use soft 300 series). That is because 416 is hard...hard because the raw billet is expensive, hard because it takes a long time to machine. However, that did not stop Wolf Tooth because there is no denying that it is the best material for those that need the ultimate durability in a chainring. These stainless steel chainrings are not only beautiful, but they will last 5-10 times longer than their aluminum versions. Compatibility: - These are functionally the same as the aluminum 104 BCD rings. - These rings fit any 104 BCD crankset. - 30t x 104 ring is the only Quarq power meter compatible 30t ring available. - For 1x9, 1x10, 1x11 and 1x12 drivetrains (including SRAM Eagle) - Compatible with all 10, 11, and 12 speed chains (Including SRAM Eagle) - If using a 9 speed drivetrain use a 10 speed chain (shifts and works well on a 9 speed drivetrain and fits the ring tighter for better chain retention). - Provide a great chainline on most boost bikes

Wolf Tooth was first to market with Cyclocross 1x specific chainrings because we saw Cyclocross as the perfect use for our patent pending Drop-Stop technology. These beautifully machined 110 BCD Asymmetric 4-bolt chainrings are optimized for your 1x Shimano CX/ Road/ Gravel drivetrain whether you run Dura Ace 9000, Ultegra 6800, 105 5800, or Tiagra 4700. They are also offset for the ideal 1x chainline. Compatibility: - These rings are for use with 110 BCD Asymmetric 4-bolt cranks. - Compatible with Dura Ace 9000, Ultegra 6800, 105 5800, Tiagra 4703, and Tiagra 4700 - Sizes 38T and larger are compatible with Dura Ace 9100, Ultegra 8000 and 105 R7000 but a slight modification is required due to a change in the crank arm profile. The 36T chainring will not work for this modification. - Mounts in the big ring position of the cranks but is offset inward for perfect chainline. - The stock 2x bolts will not work. You will need 6mm bolts which are optimized for single ring mounting. - For 1x9, 1x10, 1x11 and 1x12 drivetrains including SRAM Eagle (TM) - Compatible with all 10, 11, and 12 speed chains including SRAM Eagle (TM) - If using a 9 speed drivetrain use a 10 speed chain (shifts and works well on a 9 speed drivetrain and fits the ring tighter for better chain retention).

Wolf Tooth was first to the market with Cyclocross 1x specific chainrings because they saw Cyclocross as the perfect use for our Drop-Stop technology. Since their release, the uses for these rings has expanded beyond Cyclocross to commuting, gravel riding, mountain bikes with 5-arm crank power meters, and even full on road applications with the giant 50t rings! Compatibility: - These rings are for use with 110 BCD 5 arm cranksets. Do NOT fit Shimano DA 9000 / Ultegra 6800 - Not compatible with Campy CX10/11. - Can be mounted in either the big or small ring position of a double crankset given chainstay clearance in the small ring position. - Stock 2x bolts will not work. You will need 6mm bolts which are optimized for single ring mounting. - For 1x9, 1x10, 1x11 and 1x12 drivetrains (including SRAM Eagle) - Compatible with all 10, 11, and 12 speed chains (Including SRAM Eagle) - If using a 9 speed drivetrain use a 10 speed chain (shifts and works well on a 9 speed drivetrain and fits the ring tighter for better chain retention).

120 BCD cranksets were introduced with SRAM 2x10 drivetrains and are excellent candidates for a 1x conversion with our patented Drop-Stop chainrings. These rings will allow you to convert your 120 BCD crankset, like the SRAM XX and others, to a 1x application! Compatibility: - These rings fit any 120 BCD crankset or spider. - For SRAM cranksets you must use the stock M8.5 bolts. These are not standard bolts and Wolf Tooth's bolts will not work with this chainring. Note that only about 3 threads will engage (same with the stock SRAM rings) - For the 36t chainring and non-SRAM cranksets you will need the M8.5 bolts from Wickwerks if your crankset doesn't already have them. These bolts actually have more threads engaged and will work better than the SRAM ones. - 36t is the smallest number of teeth that fits on a 120 BCD - For 1x9, 1x10, 1x11 and 1x12 drivetrains (including SRAM Eagle) - Compatible with all 10, 11, and 12 speed chains (Including SRAM Eagle) - If using a 9 speed drivetrain use a 10 speed chain (shifts and works well on a 9 speed drivetrain and fits the ring tighter for better chain retention).

120 BCD cranksets were introduced with SRAM 2x10 drivetrains and are excellent candidates for a 1x conversion with our patented Drop-Stop chainrings. These rings will allow you to convert your 120 BCD crankset, like the SRAM XX and others, to a 1x application! - These rings fit any 120 BCD crankset or spider - For SRAM cranksets you must use the stock M8.5 bolts. These are not standard bolts and Wolf Tooth's bolts will not work with this chainring. Note that only about 3 threads will engage (same with the stock SRAM rings) - For the 36t chainring and non-SRAM cranksets you will need the M8.5 bolts from Wickwerks if your crankset doesn't already have them. These bolts actually have more threads engaged and will work better than the SRAM ones. - 36t is the smallest number of teeth that fits on a 120 BCD - For 1x9, 1x10, 1x11 and 1x12 drivetrains (including SRAM Eagle) - Compatible with all 10, 11, and 12 speed chains (Including SRAM Eagle) - If using a 9 speed drivetrain use a 10 speed chain (shifts and works well on a 9 speed drivetrain and fits the ring tighter for better chain retention).

Wolf Tooth was first to market with Cyclocross 1x specific chainrings because we saw Cyclocross as the perfect use for our Drop-Stop technology. Since their release, the uses for these rings has expanded beyond Cyclocross to commuting, gravel riding, and even full on road applications with the giant 52t rings! - These rings are for use with 130 BCD 5 arm cranksets. - Do NOT fit on Shimano DA 9000 / Ultegra 6800 - Not compatible with Campy CX10/11. - SRAM Exogram cranksets with inset nut must use stock fifth bolt + spacer(s). The Force CX1 bolt features fifth bolt with 1X specific shoulder. This kit can be found online. - Can be mounted in either the big or small ring position of a double crankset given chainstay clearance in the small ring position. - 38T important note: The chain may contact the spider arm slightly when using the 38T chainring. Wolf Tooth recommends filing a small chamfer on the spider arm but you can also just install it and let the chain do the work. This is only an issue with the 38T as the 130 BCD was designed for 39T smallest ring. - Stock 2x bolts will not work. You will need bolts like our 6mm bolts which are optimized for single ring mounting. - For 1x9, 1x10, 1x11 and 1x12 drivetrains (including SRAM Eagle) - Compatible with all 10, 11, and 12 speed chains (Including SRAM Eagle) - If using a 9 speed drivetrain use a 10 speed chain (shifts and works well on a 9 speed drivetrain and fits the ring tighter for better chain retention).

Wolf Tooth's SDM® chainrings replace your existing spider and chainring with one clean looking, light weight, and stiff piece of machined billet. These come in 3 different offsets: standard GXP, Boost and BB30. Compatibility: - These direct mount chainrings will replace your existing chainring and spider, which is attached via 3 bolts on the back side of the spider near the spindle. You will use these same 3 bolts to attach the Wolf Tooth SDM® chainring. - There are 3 offsets: Standard: 47mm chainline, 6mm offset for cyclocross and road cranks Standard: 49mm chainline, 6mm offset for GXP and long spindle BB30 Boost: 52mm chainline, 3mm offset BB30: 49mm chainline, 0mm offset for BB30 short spindle cranks - Fat Bikes: If you are planning to use this on an X9 or XX1 fat bike crankset with a 190/197 rear hub spacing use the 0 offset ring. If your fat bike has a 170/177 rear hub spacing, use the Standard 6mm offset

- Standard 4-bolt ring with Drop-Stop tooth design to prevent unwanted chain drop - Recommended for use with 10 or 11sp chain (10sp chain works on 9sp drivetrain) - Designed and manufactured in the USA from 7075-T6 aluminum alloy - 36g (30t)

This 94 BCD 5 bolt ring will serve all your Vintage crankset and Surly crankset needs! - 4 of the holes are threaded and 1 is a normal through bolt hole (done for Surly compatibility). Use a stock 10mm chainring bolt for the fifth, hidden arm. - These rings fit any 94 BCD 5 bolt crankset - For Plus size bike applications with the Surly OD crankset, e.g. Instigator and Krampus, you will need to use the stock spacers (Spacer Kit QBP Part number CR8609) that came with your 1x setup. You will also need some 16mm bolts from problem solvers. - This ring will work with your vintage 94 BCD 5-bolt cranksets!! - For 1x9, 1x10, 1x11 and 1x12 drivetrains (including SRAM Eagle) - Compatible with all 10, 11, and 12 speed chains (Including SRAM Eagle) - If using a 9 speed drivetrain use a 10 speed chain (shifts and works well on a 9 speed drivetrain and fits the ring tighter for better chain retention). - Provide a great chainline on most boost bikes.

- Road/Cross/Gravel offset ring has a reverse dish for perfect chainline - Fits Cannondale Hollowgram SI & SISL cranksets, replacing ring and spider - 48mm chainline, same as Cannondale XX1 spider. Use 10 or 11sp chain (10sp chain works on 9sp drivetrain) - Features Drop-Stop tooth design to prevent unwanted chain drop - Made in the USA from 7075-T6 aluminum alloy - 64g/68g/72g (30/32/34t)

- Cyclocross ring with Drop-Stop tooth design to prevent unwanted chain drop - Recommended for use with 10 or 11sp chain (10sp chain works on 9sp drivetrain) - Designed and manufactured in the USA from 7075-T6 aluminum alloy

These chainrings are for Race Face Cinch cranks such as Turbine, Next SL, Sixc & Aeffect. The Wolf Tooth Cinch rings feature a our patented Drop-Stop design for the best wear life, chain retention and mud clearance. We have both Boost and standard chainrings. - CNC machined aluminum ring fits Race Face cranks with Cinch System - Features Drop-Stop tooth design to prevent unwanted chain drop - Asymmetrical tooth shape for the best wear life, chain retention and mud clearance - Recommended for use with 10 or 11sp chain (10sp chain works on 9sp drivetrain) - Made in the USA from 7075-T6 aluminum alloy

Wolf Tooth's SDM chainrings replace your existing spider and chainring with one clean looking, light weight, and stiff piece of machined billet. These come in 3 different offsets: standard GXP, Boost and BB30. Compatibility: - These direct mount chainrings will replace your existing chainring and spider, which is attached via 3 bolts on the back side of the spider near the spindle. You will use these same 3 bolts to attach the Wolf Tooth SDM® chainring. There are 3 offsets: - Standard: 47mm chainline, 6mm offset for cyclocross and road cranks - Standard: 49mm chainline, 6mm offset for GXP and long spindle BB30 - Boost: 52mm chainline, 3mm offset - BB30: 49mm chainline, 0mm offset for BB30 short spindle cranks - Fat Bikes: If you are planning to use this on an X9 or XX1 fat bike crankset with a 190/197 rear hub spacing use the 0 offset ring. If your fat bike has a 170/177 rear hub spacing, use the Standard 6mm offset - If you have a BB30 crankset (30mm diameter Aluminum Spindle) this measurement will determine whether it is a long or short spindle:

It is exciting to be a part of the recent Enduro, All Mountain and Trail fueled trend that is shifting mountain bike and component design focus from "weight weenie" to "fun, functional, and DURABLE". Made from 416 stainless steel and heat-treated for hardness and strength, these chainrings are not only beautifully machined but they will stand up to whatever you can dish out. These chainrings are functionally the same as Wolf Tooth's Direct Mount for SRAM rings (dished roughly 6mm) except they are made of stainless steel for increased durability. They will have the perfect perfect 1x chainline on SRAM GXP cranks, BB30 Long Spindle cranks, SRAM Road cranks, and SRAM CX1 cranks with removable spiders. - Heat treated 416 stainless steel ring for maximum durability - Replaces the existing chainring and spider on 3-bolt GXP cranks - Asymmetrical tooth shape for the best wear life, chain retention and mud clearance - Fits SRAM S2200, S2210, X9, X0, X01, XX1, X1 and Truvativ AKA GXP cranks - Dished ring provides 49mm chainline on GXP or BB30 / PF30 long spindle - Recommended for use with 10 or 11sp chain (10sp chain works on 9sp drivetrain) - Designed and manufactured in the USA from 7075-T6 aluminum alloy - 96g (26t)

Wolf Tooth designed these bolts to be the best on the market. They have a 4mm hex socket and are 10mm long so you can use a bash ring with your chainring that has threaded standoffs like the Wolf Tooth 104 BCD 30t ring, Elliptical 104 BCD rings, 76 BCD rings and others. No nuts are included with these bolts as they are intended for use with threaded chainrings. These work great with Wolf Tooth or any other brand threaded M8 x 0.75 chainrings.

Wolf Tooth designed these bolts to be the best on the market. These optimized single chainring bolts have a 4mm hex socket on the bolt and a 6mm hex socket on the nut...that's right, no more spanner for your single ring bolts! These are 6mm long so they work perfectly with any bolt on single chainring that does not have threaded standoffs. - 6mm length - Made in the US out of 7075 Aluminum Alloy - Has hex heads on both the bolt and nut for easy installation - Max torque of 6-7 Nm with light grease on threads only

- Fits asymmetrical 96mm BCD with built-in threaded standoffs - Used on Shimano XTR M9000 and M9020 crankset (both race and trail models) - Features Drop-Stop tooth design to prevent unwanted chain drop - Mount using the stock Shimano XTR M7 chainring bolts - 49mm chainline for 28-34 tooth and 50mm for 36 tooth - Recommended for use with 10 or 11sp chain (10sp chain works on 9sp drivetrain) - Made in the USA from 7075-T6 aluminum alloy - 41g (30t)

- Fits 88mm BCD used on Shimano XTR M985 race crankset (not M980 Trail) - Features Drop-Stop tooth design to prevent unwanted chain drop - 52mm chainline - Recommended for use with 10 or 11sp chain (10sp chain works on 9sp drivetrain) - Made in the USA from 7075-T6 aluminum alloy - 44g (30t)

- For chain and derailleur alignment - 20 per bag

-Anodized aluminum for minimum weight

- Anodized aluminum for minimum weight

- CNC machined 6061 aluminum, no shift ramps, hard anodized for durability - Excellent for Singlespeed/fixed gear applications

- CNC 6061 aluminum chainring with standard teeth

- Black Anodized with CNC machined ramps, steel pins

- chrome plated steel for maximum durability